I'm new to the site and the beast style hunting. I recently purchased an XOP Air Raid and climbing sticks, so i am completely mobile for the first time. I've found some cool stand modifications on the site, but was wondering if anyone had any tips or tricks for attaching and/or securing a pull cord for my bow on this type of setup? I currently just have the cord tied to the platform and wrapped around when I'm packing it in. But I know there are a lot smarter and more creative people out there than myself- so I figured I would ask if anyone is willing to share.
Thanks
Bow Cord modifications
-
- Posts: 35
- Joined: Sat Jan 14, 2017 1:18 am
- Location: MO
- Status: Offline
- Jonny
- 500 Club
- Posts: 5762
- Joined: Wed Oct 19, 2016 3:11 am
- Location: In a van down by the river
- Status: Offline
Re: Bow Cord modifications
I have seen something similar to what you do. Wrap around the stand platform and have a bungee on the end with a cheap carabiner. Hook the carabiner on the stand so that the bungee is under tension. youtube search public land hunters stand modifications, he shows how he did it. Might try it with my stand.
The other one that I and many others do, is a 30' string or ribbon and wrapped in a figure 8 around your thumb and pinky and put into a pocket. Use a figure 8 otherwise you are in for about 5 minutes of swearing under your breath while you untangle it. You could say I have done that before
And welcome to the beast!
The other one that I and many others do, is a 30' string or ribbon and wrapped in a figure 8 around your thumb and pinky and put into a pocket. Use a figure 8 otherwise you are in for about 5 minutes of swearing under your breath while you untangle it. You could say I have done that before
And welcome to the beast!
You have a monkey Mr. Munson?
- Jlarsc
- Posts: 8
- Joined: Thu Sep 01, 2016 2:19 pm
- Status: Offline
Re: Bow Cord modifications
https://www.amazon.com/Pine-Ridge-Arche ... B000LH7VH2
I use this strap on a reel. Fits in my pocket and doesnt get all tangled like a rope.
I also clip it to a fannypack and it fits in the water bottle holder.
I use this strap on a reel. Fits in my pocket and doesnt get all tangled like a rope.
I also clip it to a fannypack and it fits in the water bottle holder.
- tgreeno
- 500 Club
- Posts: 4770
- Joined: Fri Feb 19, 2016 5:06 am
- Location: WI
- Status: Offline
Re: Bow Cord modifications
I used this the last 2 seasons. The flat cord doesn't tangle like a round cord. And it's all rubber coated, nothing to make noise. I carry it in my pocket, and tie the end to back of my belt after I attach it to my bow, as I'm setting up my sticks.
http://www.basspro.com/Hawk-Twist-Tie-H ... extensions
http://www.basspro.com/Hawk-Twist-Tie-H ... extensions
--------------------------------------------------------------------------------------------------------------
It's better to keep your mouth shut and appear stupid, than to open it an remove all doubt
It's better to keep your mouth shut and appear stupid, than to open it an remove all doubt
-
- Posts: 35
- Joined: Sat Jan 14, 2017 1:18 am
- Location: MO
- Status: Offline
Re: Bow Cord modifications
hmm that looks pretty cool. I think I'll give it a try thanks!
- stash59
- Moderator
- Posts: 10078
- Joined: Thu Nov 27, 2014 8:22 am
- Location: S Central Wi.
- Status: Offline
Re: Bow Cord modifications
I've tried the reels. Sooner or later I ended up banging it on the stand.
The trick I found is use a thicker rope. At least 3/16". Even if they do tangle. The tangles don't get as tight as a string. Plus because of the added thickness the chance for tangles decrease. The little bit of extra room it takes is worth it in the long run.
Also when pulling the bow up. Try to pay attention and lay it out more on nearby branches. In a way that will minimize the tangles. I always got the worst tangles while pulling up the bow. Especially when extra high in a tree. Wrap it up once you've got your bow in the tree and put it away. This will make lowering the bow easier. Haven't used it much but yes the figure 8 method works quite well.
I also only like to have just the right amount of rope lowered to get the job done. Why lower 30' of rope if your only 12' high. I actually try to leave the bottom end of my rope end up at chest level. This is extremely important if there is snow on the ground. But is good for dry ground too. It keeps sticks, snow and other debris out of wheels, wheel/string junctions and sights. Plus any where else you don't want junk.
tgreeno how are those wraps holding up on that rope. What are they actually made of? They look slick.
The trick I found is use a thicker rope. At least 3/16". Even if they do tangle. The tangles don't get as tight as a string. Plus because of the added thickness the chance for tangles decrease. The little bit of extra room it takes is worth it in the long run.
Also when pulling the bow up. Try to pay attention and lay it out more on nearby branches. In a way that will minimize the tangles. I always got the worst tangles while pulling up the bow. Especially when extra high in a tree. Wrap it up once you've got your bow in the tree and put it away. This will make lowering the bow easier. Haven't used it much but yes the figure 8 method works quite well.
I also only like to have just the right amount of rope lowered to get the job done. Why lower 30' of rope if your only 12' high. I actually try to leave the bottom end of my rope end up at chest level. This is extremely important if there is snow on the ground. But is good for dry ground too. It keeps sticks, snow and other debris out of wheels, wheel/string junctions and sights. Plus any where else you don't want junk.
tgreeno how are those wraps holding up on that rope. What are they actually made of? They look slick.
Happiness is a large gutpile!!!!!!!
- Horizontal Hunter
- 500 Club
- Posts: 2938
- Joined: Thu Jul 31, 2014 1:08 pm
- Location: Western Massachusetts
- Status: Offline
Re: Bow Cord modifications
I just use 25' of paracord. If you wrap it up the way he shows how to towards the end of the video it won't tangle. Been doing it this way for years.
Bob
https://youtu.be/U-VVrq4E7eY
Bob
https://youtu.be/U-VVrq4E7eY
Vegetarian: vejiˈte(ə)rēən/noun: old Indian word for lousy hunter.
Excalibur Exocet, GT Laser II, 2" Bhoning Blazers 125g NAP Spitfire
Excalibur Exocet, GT Laser II, 2" Bhoning Blazers 125g NAP Spitfire
- tgreeno
- 500 Club
- Posts: 4770
- Joined: Fri Feb 19, 2016 5:06 am
- Location: WI
- Status: Offline
Re: Bow Cord modifications
stash59 wrote:
tgreeno how are those wraps holding up on that rope. What are they actually made of? They look slick.
They are rubber coated wire...After probably 80-100 hunts, I just had the 1/3 of the end of one of the wires break off. Still plenty of wire to secure the bow, and used it like that most of December. The wires are twice as long as they need to be when new.
--------------------------------------------------------------------------------------------------------------
It's better to keep your mouth shut and appear stupid, than to open it an remove all doubt
It's better to keep your mouth shut and appear stupid, than to open it an remove all doubt
- Jeff25
- Posts: 271
- Joined: Tue Oct 06, 2015 10:52 am
- Location: Midwest
- Status: Offline
Re: Bow Cord modifications
I tie a small loop onto my stand, then I figure 8 my bow rope between my pinky and thumb making 2 loops. I leave about 8-10" of the bow rope and wrap the figue 8 to hold it tight then clip the carabiner that's on the end of my bow rope through one of the figure 8 loops, and to attach it to the stand I clip the carabiner to the loop on the stand. If that makes since lol
-
- Advertisement
Who is online
Users browsing this forum: KRONIIK, PoppaOtt84, TrendictionBot and 105 guests