If any of you guys shoot and dont need you brass, of know where some is located Id appreciate it
I am working on a couple projects and need brass for a [glow=red].444 Marlin[/glow] and [glow=red]270 WSM[/glow]
T-H-A-N-K Y-O-U!!
Tony
BRASS NEEDED!
- backstraps
- Moderator
- Posts: 10122
- Joined: Sun Jun 24, 2012 4:44 pm
- Location: Tennessee
- Status: Offline
- backstraps
- Moderator
- Posts: 10122
- Joined: Sun Jun 24, 2012 4:44 pm
- Location: Tennessee
- Status: Offline
Re: BRASS NEEDED!
found some 270 wsm online
Any of you midwest straight cartridge hunters have any spent .444 cases you dont want?
Any of you midwest straight cartridge hunters have any spent .444 cases you dont want?
- jwilkstn
- 500 Club
- Posts: 1467
- Joined: Sat Aug 27, 2016 6:01 am
- Facebook: https://www.facebook.com/jason.wilkerson.71
- Location: The hills of Southern Middle Tennessee
- Contact:
- Status: Offline
Re: BRASS NEEDED!
No help, sorry, but just curious about your .270 wsm loading? I bought several boxes of factory Federals when I bought my rifle, but I haven't yet been able to load up anything more accurate than them.
Not all those who wander are lost...
- backstraps
- Moderator
- Posts: 10122
- Joined: Sun Jun 24, 2012 4:44 pm
- Location: Tennessee
- Status: Offline
Re: BRASS NEEDED!
A few years ago, maybe 5 years ago Lade aka DA on the tn site helped me with some loads for one of my 270wsm that gun loved factory Winchester SIlvertips, both 130 and 150gr
We played around with seating depths, powders, and loads until that gun with a crappy tuned factory trigger will shoot 1/2" moa and holds tight to 500
I have a Rem 700 with a Jewell, bedded Bell Carlson, Nightforce steel rail and rings, and Viper PST glass. I have played with loads here at 400, 600 and 750
It will shoot .175" off the bench @100. I shot a 3" at 650yds
That gun really likes 140gr Accubonds, over MagPro or RL-22 powder. Usually seating a thousandths of the lands.
I normally have to tweak pet loads for a particular gun's barrel.
We played around with seating depths, powders, and loads until that gun with a crappy tuned factory trigger will shoot 1/2" moa and holds tight to 500
I have a Rem 700 with a Jewell, bedded Bell Carlson, Nightforce steel rail and rings, and Viper PST glass. I have played with loads here at 400, 600 and 750
It will shoot .175" off the bench @100. I shot a 3" at 650yds
That gun really likes 140gr Accubonds, over MagPro or RL-22 powder. Usually seating a thousandths of the lands.
I normally have to tweak pet loads for a particular gun's barrel.
- jwilkstn
- 500 Club
- Posts: 1467
- Joined: Sat Aug 27, 2016 6:01 am
- Facebook: https://www.facebook.com/jason.wilkerson.71
- Location: The hills of Southern Middle Tennessee
- Contact:
- Status: Offline
Re: BRASS NEEDED!
All I can say is WOW
I thought my setup was accurate haha
I'm shooting a Tikka T3, all stock except a Limbsaver recoil pad. It'll shoot the Federal 130 grains .355" at 100 yards. Have shot .7" groups at 200 and 1.3" at 300. Only shot steel beyond that. I'm clearly happy with that lol.
Can't recall which powders I've tested, but tried various charges and seating depths with the 140 Accubonds. They shoot well enough for my skill in real world hunting, several sub-moa. Just nothing spectacular.
I am newer to reloading also, so I'm not completely sure my processes aren't holding me back but that's a whole other forum lol
I thought my setup was accurate haha
I'm shooting a Tikka T3, all stock except a Limbsaver recoil pad. It'll shoot the Federal 130 grains .355" at 100 yards. Have shot .7" groups at 200 and 1.3" at 300. Only shot steel beyond that. I'm clearly happy with that lol.
Can't recall which powders I've tested, but tried various charges and seating depths with the 140 Accubonds. They shoot well enough for my skill in real world hunting, several sub-moa. Just nothing spectacular.
I am newer to reloading also, so I'm not completely sure my processes aren't holding me back but that's a whole other forum lol
Not all those who wander are lost...
-
- Advertisement
Who is online
Users browsing this forum: No registered users and 22 guests